10 Industrial Electrical Training Video Course Library [RECENT — ANTHOLOGY]
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Digital multimeter (DMM) basics: V, A, Ω, continuity | Measure line voltage (120V/480V) | | 2 | Clamp meter – measuring current without breaking circuit | Measure motor FLA in a panel | | 3 | Insulation resistance tester (megohmmeter) | Test motor winding insulation | | 4 | Non-contact voltage tester & solenoid tester | Verify absence of voltage | | 5 | Understanding test lead categories (CAT III / CAT IV) | Compare meters for industrial use |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | One-line diagrams vs. wiring diagrams vs. ladder logic | Trace power from utility to motor | | 2 | Wire numbering & terminal strip labeling | Follow a wire from page 3 to page 10 | | 3 | Finding an open circuit – step-by-step voltage method | Locate a broken wire in a control loop | | 4 | Finding a short circuit – resistance method | Blown fuse investigation | | 5 | Ground fault location using a megohmmeter | Isolate a wet motor winding |
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Contactors – coil, contacts, arc chutes, enclosure types | Open a NEMA contactor | | 2 | Manual motor starters – toggle & pushbutton | Wire a simple start/stop circuit | | 3 | Magnetic motor starter – 3-pole contactor + overload relay | Assemble a starter on a DIN rail | | 4 | Overload relays – thermal (bimetallic) vs. electronic | Trip test with a heat gun | | 5 | Selecting starter size based on motor HP & voltage | Sizing exercise for a 25 HP motor |
Calculate expected full-load current given HP, voltage, and efficiency. Course 4: Motor Starters & Contactors Focus: Manual and magnetic starters, contactor operation, overload relays. 10 Industrial Electrical Training Video Course Library
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Control relays (ice cube, slim interface, power relay) | Wire a holding (seal-in) circuit | | 2 | On-delay & off-delay timers (solid-state & pneumatic) | Build a star-delta timer circuit | | 3 | Proximity sensors – inductive (metal) vs. capacitive (all materials) | Detect a bolt vs. a plastic block | | 4 | Photoelectric sensors – through-beam, retroreflective, diffuse | Align a through-beam sensor | | 5 | Introduction to ladder diagrams (NO/NC contacts, coils) | Convert a relay schematic to ladder |
Identify 5 code violations in a photo of a real industrial panel. Production & Delivery Notes | Element | Recommendation | |---------|----------------| | Video length per course | 45–75 minutes (broken into 5–8 segments of 5–12 min) | | Instructor | Licensed master electrician or EET with 10+ years industrial experience | | Visual style | Split-screen: instructor + live panel / motor / VFD + animated circuit diagrams | | Hands-on materials | Each course includes a downloadable worksheet, schematic, and quiz | | Certification | Completion badge + .pdf certificate per course | | Target software playback | LMS (SCORM), YouTube Unlisted, or company training portal | Optional Add‑On (11th course – Bonus) PLC & HMI for Electricians (Basics of digital inputs/outputs, ladder logic vs. relay logic, and HMI navigation for troubleshooting.)
Design a conveyor start/stop with a 5-second delayed start. Course 7: Variable Frequency Drives (VFDs) – Setup & Troubleshooting Focus: VFD components, programming, motor protection, and common faults. | Segment | Topic | Key Demo |
Using a schematic, find why a pump will not start – all indicators are off. Course 9: Electric Motor Maintenance & Failure Analysis Focus: Megger testing, bearing replacement, alignment, and winding evaluation.
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | How 3-phase induction motors work – rotating magnetic field | Animated stator/rotor interaction | | 2 | Motor nameplate: voltage, FLA, RPM, service factor, insulation class | Read 5 real nameplates | | 3 | Single-phase vs. three-phase motors | Capacitor-start motor teardown | | 4 | DC motors – series, shunt, compound | Small DC motor demo with speed control | | 5 | Motor efficiency & power factor basics | Compare efficiency labels |
Diagnose a blown fuse using continuity and voltage measurements. Course 3: AC/DC Motor Theory & Nameplate Interpretation Focus: Induction motors, DC motors, nameplate data, and basic motor physics. electronic | Trip test with a heat gun
| Segment | Topic | Key Demo | |---------|-------|-----------| | 1 | Electrical hazards in industry (shock, arc flash, blast) | Arc flash simulation video | | 2 | NFPA 70E categories & approach boundaries | PPE selection chart walkthrough | | 3 | Proper use of insulated tools & voltage testers | Testing before touching | | 4 | Lockout/Tagout (LOTO) – 6-step procedure | Live LOTO on a motor starter | | 5 | Emergency response & first aid for electrical shock | Rescue hook demonstration |
Troubleshoot a contactor that chatters when energized. Course 5: Overcurrent Protection – Fuses & Circuit Breakers Focus: Fuse types, breaker trip curves, selective coordination, and short-circuit ratings.
Choose a fuse type for a motor circuit with high inrush current. Course 6: Control Circuits – Relays, Timers & Sensors Focus: Industrial control logic, timing relays, proximity/photo sensors, and basic ladder logic.
Fix a VFD tripping on “Overvoltage” during deceleration. Course 8: Electrical Schematics & Panel Troubleshooting Focus: Reading industrial drawings, finding shorts, opens, and ground faults.
A 50 HP motor trips on overload – megger reading is 2 MΩ at 1000V. Repair or replace? Course 10: Industrial Control Panel Design & NFPA 79 Focus: Panel layout, wire bending space, grounding, and electrical standards.